Sanding cabinets

What is the easiest way to sand cabinets? How to finish unfinished cabinets? Proper sanding is necessary to get a smooth final coat of paint or stain. Sand the finish from the cabinets , trim and drawers with 120-grit sandpaper. If the cabinets are stained or coated with a single layer of clear finish, you may not need to use paint stripper.

Delicate sanding is done by hand with custom-made tools. Cut a piece of 100-grit sandpaper into square pieces and use your fingers to shape it around rounded moldings and trim. Wrap strips around a dowel and use the dowel to sand curves and profiled moldings. This creates a truly random sanding pattern , which removes wood quickly and minimizes swirl marks. This speedy randomness also allows you to smooth joints where the rails and stiles of your cabinets meet at right angles.

I’ve found that most cabinets people want to repaint are in pretty good shape, and they don’t mind if you can see a little wood grain,” says Dowding. Sand with the grain if the cupboards are made of wood. I used my Ryobi orbital sander on all the flat surfaces (basically anything it could reach), and used the sanding blocks for the smaller, harder to reach moldings and corners. The key here is to sand some of the existing.

Photo 7: Sand the cabinets smooth. Sand the spackling compound flush to the cabinet surface with 120-grit sandpaper after it dries. Depending on temperature and humidity, drying time will vary from a few hours to overnight. Look for areas needing additional filling and reapply spackling if necessary.

First, it removes any existing sheen or protective sealant from cabinet drawer and door fronts, allowing primer and paint to bond effectively to the surface. Once applied to areas prepped with wood filler or putty, it also helps to smooth out any existing scratches, dings or nicks. Sanding is important for several reasons. But if the doors are smooth (not slick) to the touch, you can likely skip the sanding step, as long as you do a few bits of prep first!

Sand and stain the faces of the cabinets using the same sanding and staining techniques as for the doors. Wet sanding is generally carried out when a high shine is required. Tip : When sanding with an orbital sander, always sand with the grain.

If you want to take the cabinets back to the original woo apply a clear varnish or polyurethane finish or stain previously painted cabinets , you will have to strip all the paint off the cabinets using strong chemicals, followed by sanding. Contrary to popular belief, if you have old stained oak cabinets , you should NOT be using sandpaper on them prior to painting them white! Yes, I know this goes against a lot of what you hear elsewhere. But, I can tell you for a fact that if you sand your cabinets you run the risk of a bad paint job.

I speak from experience! Even if your cabinets are in near-perfect condition, you still have to sand them so the paint will stick. If you prep with the right products, you can save yourself the hassle with these tips! The kitchen, Saturday morning: Complete with dirty dishes in the sink.

Mom and Granny came over to help me get started. Pictured here is a quick discussion about the game plan. Free 2-day Shipping On Millions of Items.

Once you’re finished with the stripping agent, use a wood filler to repair any holes or scratches in the woo and then lightly sand out the patch once. If your cabinets are painted… Before embarking, remove one of the doors and sand off a small area of the finish on the back. Use a sanding sponge to dig into any tough areas that need special attention or corners that are hard to get with your sander. Check on wood filler repairs and sand those areas to match. Sand the surfaces of the doors, drawer faces and cabinet frame to create a smooth surface for priming.

Remember, the higher the “grit number, the smoother the finish. You do need to sand the cabinets …that’s how the paint adheres (in the same way that you need to sand the floors for the stain to properly penetrate). An you do need multiple coats of paint (at least coats, but usually 3….and yes, I know people that have done it and some of them even needed 3-coats). The purpose of this sanding is to scuff up and dull the surfaces so that the primer will adhere well. Use a small piece of sandpaper for rounded or contoured surfaces.

Browse Our Variety Of Sandpaper—Find All The Supplies You Need Today.